IP-blocks FOR VIDEO, GRAPHICS, BIG DATA, DATA ACQUISITION
These IP blocks are also listed at:
- Design & Reuse (The largest IP portal in the world)
- EIPC (Japanese IP portal)
- Xilinx
BIT-MIPI, a Very Compact CSI-2 Camera Interface
To transfer the data from the sensor in a modern camera, MIPI CSI-2, a popular high speed serial interface specification, is often used. For this interface, BitSim has developed two very compact CSI-2 cores using only 500 LUTs, BitCsi2Tx and BitCsi2Rx that provide a low-power and cost-effective solution for your camera application. The design is … Continue reading BIT-MIPI, a Very Compact CSI-2 Camera Interface
High-level platform for camera development
Use BitSim’s high-level platform SpiderPig for developing your camera! Develop your image processing algorithms in Python and accelerate the functionality in FPGAs, either in the CPU/SW-part (PS) or in the parallel logic part (PL). In its basic version, it comes as an embedded Video-over-ethernet system featuring both an RGB- and IR-sensor, via the MIPI CSI-2 … Continue reading High-level platform for camera development
MAGIC ADDA DATA ACQUISITION
BitSim’s FMC data acquisition board MAGIC ADDA enables both ADC, Analog to Digital conversion and DAC, Digital to Analog conversion at a cutting edge of technology in terms of high speed 4.8 GHz. The design can be easily adapted for different applications where data collection is important, for example RF, microwave, optical and Big Data. … Continue reading MAGIC ADDA DATA ACQUISITION
BIT-10G-UDP ETHERNET
For embedded applications with extremely high demands for fast data transfers, BitSim has launched its IP core, Bit-10G-UDP Ethernet. This core is a real-time offload engine where the communication is accelerated in the FPGA, and uses the 10 Gb/s Ethernet protocol to the host. Standard functions for transmit, receive, ARP-handling, AXI-stream and loop back are … Continue reading BIT-10G-UDP ETHERNET
BIT-MULTI-ETHERNET – CAMERA
A full embedded camera-system is provided with the Bit-Multi-Ethernet-Camera, consisting of an integrated chain of IP blocks. It feeds a camera sensor’s video stream via RTP to an UDP/IP-Ethernet Interface. All processing of the video stream and protocol handling is done in hardware. Only a lens, a camera sensor, PHY components and housing are needed … Continue reading BIT-MULTI-ETHERNET – CAMERA
BIT-1G-UDP ETHERNET
To efficiently transfer large amounts of data and off-load the embedded processor, BitSim is offering its IP core, Bit-1G-UDP Ethernet. This core offloads an embedded processor with the communication accelerated in the FPGA, with more than ~900+ Mb/s of effective data transfer rate. Standard functions for transmit, receive, ARP-handling, AXI-stream and loop back are included.
BIT-IMAGER CAMERA PLATFORM
Our building block Bit-Imager is basically an electronic card adapted to easily produce a CMOS-based stereo camera with USB3 interface. Regardless of the application, size or other imaging needs, if you need a camera with a high packing density and integrated circuit we can easily adapt this platform to your needs. You decide if the … Continue reading BIT-IMAGER CAMERA PLATFORM
BADGE – 2D GRAPHICS
Would you like to display text, graphics or video on a built-in display? Or even mix video and graphics on the display? This becomes easy with BADGE – BitSim Accelerated Display Graphics Engine, that supports both TFT and STN display. BADGE is a configurable IP block with an advanced 2D graphics controller for both ASIC … Continue reading BADGE – 2D GRAPHICS
Ultra High-Speed Acquisition Board
BitSim’s UHAB board enables both ADC, Analog to Digital conversion and DAC, Digital to Analog conversion at high sampling speeds. Learn more about UHAB here
ADC130
BitSim’s FMC Data Acquisition board ADC130 is designed for applications needing high resolution Analog to Digital Conversion. It provides sampling up to 130 MHz at 16 bits resolution.